The G2 PWM controller from Creative Werks is an extremely robust and versatile controller that can be used for full variable speed control on any fan, pump, or any other device with a DC motor.
Here we'll flesh out and expand on some common use cases to show just what it can do.
Let's start by covering the basic wiring requirements and considerations for the controller. For full instructions and further details, click here.
The G2 controller features three M6 screw holes for high current power, ground and the high-current output.
-
High Current Power & Ground
- The power points are solid brass, and are raised and isolated from the coated aluminum controller case, so no worries about shorting out.
- Basic M6 (1/4in) eyelets can be used. Adapter studs are available to make these RadLok connections, but my honest preference is the screws for simplicity, which also allows you to stack the fan grounds on the ground input.
- The G2 controller is capable of handling 70A max continuous at 12v. The power input should be fused according to what your fans draw. For example, if you're using the controller to run two brushed fans that each draw a max of 25A, we recommend to fuse the controller at 50 - 60A, depending on necessary headroom.
-
High-Current Output
- The third M6 screw hole is the high-current output, which will power the fans directly in brushed motor applications. See below examples for further details.
Additionally, the controller features an integrated 12-pin Deutsch DT-style connector. Certain pins are only used for specific applications, and may not be required.
- Switched 12v -This is a low-current "wakeup" signal to the controller. It is recommended to connect this to a clean switched 12v source. With no power applied to this pin, there is zero parasitic draw from the G2, meaning no need to worry about it draining your battery from prolonged periods of sitting.
- Manual Override - Apply 12v+ to this pin to override motor control to high speed. This can be used for manual fan override, or tied to the A/C request.
- Resistive Temp Sensor Input - This is the signal input for the coolant temperature sensor input. See examples 1 & 2 below.
- Secondary Relay Control Output - This is a low-side (ground) output that can be used to kick on a relay for an additional fan, such as for a transmission or auxiliary cooler. It is fully programmable for the temperature it activates. See example 4 below.
- 20-150Hz PWM Input - This pin is can be used to have an aftermarket ecu, such as Holley, Haltech, Emtron, etc command the G2 using an ecu output. See example 3 below.
- 0-5v Analog Input - This is a signal input that can be used with a pressure, position or other 0-5v type sensor. Typically not used with fan control applications.
- 5v Sensor Supply - For supplying 5vdc to a sensor for using the analog input (pin 6). Typically not used with fan control applications.
- 100 Hz PWM Output 1 - This pin is used in applications where the G2 is commanding brushless fans. See example 2 below.
- 100 Hz PWM Output 2 - See pin 8 above, example 2 below.
- Ground Supply - This pin is a ground provision, used for grounding sensors. Do NOT wire this pin to ground. Intended for grounding the temperature / pressure sensors, and can also be used to provide ground for the CAN to USB dongle as needed.
- CAN Hi - The G2 controller is configured using the simple and intuitive program, and uses CAN-to-USB to communicate with your laptop. Future updates will also allow for full CAN communication and integration with various ECU's and other modules.
- CAN Lo - See CAN Hi above.
Example 1 - Standalone (Temp Sensor) Control for Brushed Fan(s)

This may be the most basic and common use-case for the G2 with radiator fans. In this scenario, the controller is entirely self-contained, allowing for sophisticated fan control on carbureted or diesel engines, or older vehicles that otherwise don't have integrated electric fan control.
It relies on a commonly-available GM-style temperature sensor, which can be installed in the block, head or intake manifold of the engine. The sensors can be easily sourced from any parts store with M12 threads for LS applications, or 3/8npt threads for about any other engine.
Note that rather than staging the fans one after the other, the controller uses its single high-current output to run both fans together. The controller is made for the most extreme of heavy-duty applications, capable of handling up to 24v, and handles up to 70A continuous at 12v.
So, instead of turning on one fan at full speed, then having the second join in at full speed once temps climb further, both fans ramp in gently to keep temps managed in a refined manner. The controller will soft start the fans, which extends fan life and keeps the vehicle's battery and entire electrical system happier. It's capable of running most brushed fans as low as approximately 25% of their full speed. For comparison, running both fans at 50% rather than one fan at 100% makes for more balanced and consistent cooling across the full surface of the radiator.
Example 2 - Standalone (Temp Sensor) Control with Spal Brushless Fan(s)

What about the newer brushless fans from Spal? The G2 has a place with them, too. Several variants of this fan were used in 2018+ GM applications, making for a pretty affordable fan that flows an extremely high amount of air, available from the junkyards and parts houses nonetheless.
These fans were designed for variable speed control, as they do have integrated controllers, but the controller has to get a speed input from somewhere. They rely on a 128Hz pulsed input for speed control, and have specific thresholds at which they error out, both high and low, meaning you can't just ground the control wire to override the fan to full speed. ~16% duty cycle is the minimum speed input for these fans, and ~94% is the maximum, meaning they shut down with any pulsed signal above or below these thresholds.
If you're adding one of these fans to an 07+ GM truck, you can simply pin into the factory ecu, as they have the ability to control PWM fans. Say you're putting these fans on a 99-07 truck, or an OBS, or anything else that's carbureted, diesel or otherwise. The G2 can be used to seamlessly drive these fans.
Pins 8 and 9 on the 12-pin DT connector are there precisely for controlling these types of fans. Note how the fans are wired direct to battery power, and the high-current output stud from the G2 controller is not used. Because of this, the power input stud on the G2 can be supplied with switched power at a much smaller size of wire (18awg).
The manual override pin can still be used. When configured properly, the PWM output(s) will ramp to the maximum 92% duty cycle when the override input is activated.
Example 3 - PWM Control of Brushed Fans With an Aftermarket ECU

This configuration gives smooth and refined fan control on a vehicle equipped with an aftermarket ecu, such as Holley EFI, Haltech, Emtron, MoTec, etc. The efi system monitors coolant temperature through the temp sensor that's already on the engine, eliminating the need to mount an additional sensor.
An ECU output is then wired to pin 5 of the G2 controller, and configured in the ECU's software. The G2 is then commanded to modulate the fans based on the duty cycle of the signal it's receiving from the ECU.
The control strategy from the ECU can be as simple as a 1D table that modulates the frequency it's sending to the G2 based on temperature alone, but th advantage here is that additional factors can be layered into the behavior of the ECU's output. Depending on the capabilities of the EFI system you're using, a 2D, 3D or even 4D table can be used to modulate fans based on a combination of engine temp, air temp, RPM, vehicle speed, and more. Layer in A/C relay control or clutch status, and the override pin is no longer needed, simplifying wiring even further.
You may be asking, why not just use the ECU to control regular solid-state relays? The critical difference here is the frequency at which the fans are pulsed. Most ECU outputs are only capable of pulsing at a maximum 1kHz. Depending on the quality of the SSR you use, the frequency of the controlled output from the relay to the fan may be even less. This is way too low of a frequency for properly controlling brushed motors, which can lead to rapid deterioration, fan failure and controllability issues. The G2 high-current output of the G2 controller operates at a staggering 10kHz, which is excessively higher than any other "comparable" controller, but is really the necessary frequency for refined control and proper fan life expectancy.


Share: